Sterling Silver Crescent and Bead Earrings
Components NEEDED
3" 4 x 1 mm sterling silver rectangle wire
20-just one 'Λ* head pins
Two turquoise disc beads
A person Vi* one.7 mm black hollow rubber tube
Two sterling silver ear wires
What guidance would you give you a starting artist?
“Do That which you like. Explore various media. Promote on the selective, constrained, foundation at the outset to check out what works or what does not work for you before you leap into A significant outlay of money and effort.*
-Sally J. Phillips Jewellery Designer
Equipment Wanted
Ruler
Marker
Jeweler's observed or tin snips Protection Eyeglasses Tricky, flat area Awl
Hammer /is" drill little bit
Hand-held rotary tool, flex shaft, or drill press File
Fine grit sanding pad
Ring mandrel
Rawhide mallet
Two pairs of chain nose pliers
Scissors
Wire cutters or tin snips Round nose pliers
1.Use the ruler to measure and mark two 1 Vi’ pieces of 4 x one mm rectangle sterling silver wire.
2Using a jeweler's observed or tin snips, cut the 4 x one mm rectangle sterling silver wire into two one Vi’ lengths.
three.File each end of the 1Vi" rectangle wire pieces to remove any burs or rough edges.
If desired, you can use the file to round the ends of the rectangle wire parts. Utilize a great grit sanding pad to go around the region in which you have submitted to sleek the sides and take away any file marks.
four.Make use of the ruler to measure and mark /*." from a single stop in the 1 Vi’ pieces of rectangle wire and location a mark in the center of the wire. This is where you can drill the holes to slip The pinnacle pins by.
five.Place with your security glasses!!! Spot the 1 Vi" rectangle wire pieces onto a hard, flat floor. Position The purpose on the awl about the mark that you just manufactured Vm,' from one particular conclude on the rectangle wire items, and firmly strike when on the very best from the awl with a hammer. This will make a pilot gap for drilling holes into your rectangle wire.
Sterling Silver Crescent and Bead Earrings
Chapter five
six.Utilizing a /is" drill bit. drill holes into 1 end of the rectangle wire parts that has a handheld rotary Resource, flex shaft, or drill push (although nevertheless sporting your safety Eyeglasses!).
seven.Utilize the file or high-quality grit sanding pad to eradicate any burs or tough edges still left from drilling holes to the rectangle wire items.
8.Curve each 1W pieces of rectangle wire right into a “C" form utilizing a ring mandrel and rawhide mallet. If you do not have a ring mandrel and rawhide mallet, use two set of chain nose pliers. Keeping one particular pair of pliers in Every hand, grasp each close with the one Vi* rectangle wire piece With all the pliers and gently bend the rectangle wire right into a “C* condition. Assess the two from the C-shaped rectangle wire parts and alter the curves so that they are similar in si2e. Established these apart.
9.Use the ruler to evaluate and mark the rubber tube into 4 equal pieces measuring Vm’ Each individual. Use scissors to chop the rubber tube.
10.Place the turquoise disc bead on to The top pin and include one V·' bit of the rubber tube, area The top pin through the gap while in the C-shaped rectangle wire, and then increase the opposite V«" piece of rubber tube.
thirteen. Maintain The top pin with the bead, rubber tube, as well as rectangle wire on it in a single hand Using the wire that you bent pointing towards you. Using the round nose pliers, grip the top of The top pin wire that's pointing Mens Ring towards you and roll it faraway from you (consider turning the ignition key to get started on your vehicle). Release the pliers from The pinnacle pin wire.
At this point, the opening in the loop at the highest of The top pin wire should however mens ring be huge enough to slide the ear wire on. After you increase the ear wire, Mens Ring make use of the round nose pliers to grasp the loop of The pinnacle pin mens ringMens Ring wire and roll it closed. You can use the spherical nose or chain nose pliers to adjust The form in the loop at the top of The top pin if you have to.
eleven. Make use of the ruler to evaluate and mark /(.’ earlier mentioned the top bit of the hollow rubber tube. With all the wire cutters or tin snips, cut The top pin wire Yu.’ above the best in the hollow rubber tube.
twelve. Make use of the chain nose pliers to bend the head pin wire close to the top with the rubber tube at a ninety-degree angle.
fourteen. Repeat these measures for the 2nd earring.